Képek

Nagy_Extra 018.jpg

Belépés



Látogatóink:

Oldalainkat 104 vendég böngészi
Tartalom találatai : 1377150
RCS-1 English PDF Nyomtatás E-mail
Írta: Magi István   
2011. május 02. hétfő, 16:16

RCS-1 switch board allows the models through a multi-channel servo-electric appliances,
consumer on and off. The switch has 8 channels, which are found between the universal and
program-controlled switch outputs.
The universal output that we may enter into any on or off as desired consumer, which is
programmed to the appropriate after TX (servo direction, end position) simply on or off.
The outputs are servo-controlled by programs a predetermined position depending on a
switching algorithm to run. RCS-1 versions of these algorithms are programmed different,
thus, the model optimized for the needs of the individual.
Currently available programs:

RCS-1A – for plane
RCS-1B – for car models
RCS-1C – Universal purposes.
RCS-1D - Independent 5pcs Switch (NEW!)

The outputs control LEDs, relays, and other consumers to conclude that the power the servo
circuit (board) system voltage in Receiver . Accordingly so that consumers can be used that
are capable of direct power supply voltage (5V or 6V). The LEDs on the line by attaching a
ballast resistor should be inserted (details can be found below)! Relays using 5V DC coil use.
The case of so-called piezo speaker, use build in oscillator variations.
Outputs programmed as appropriate for each function correctly only if adequate space is
connected to the channel controller.
For example, the indices of the government channel only work correctly, or the plane is
proportional to the output of the throttle afterburner effect the site.
A more detailed description of the programs is below.
Common technical parameters:
Warning!
The device is only normal (FS; Fast Speed) output with customers works! Do not use HS,
HRS (High Speed) mode on!
- 8-channel, servo-style outputs
- per output max. 500mm load,
- All outputs are equipped with safetty diode,
- 5V and 6V system voltage usability
- 1-channel input power (normal, a PPM-18mS)
- Each channel (common jumper switchable) with LED
feedback
- 2 jumpers and setup,
- 59mm x 33mm PCB size,
- 16g weight
The "LED" may be inscribed above the internal jumper indicator LEDs turn on and off (open
= disabled). This will reduce fuel consumption.

Common technical parameters:


Warning!
The device is only normal (FS; Fast Speed) output with customers works! Do not use HS,
HRS (High Speed) mode on!

- 8-channel, servo-style outputs
- per output max. 500mm load,
- All outputs are equipped with safetty diode,
- 5V and 6V system voltage usability
- 1-channel input power (normal, a PPM-18mS)
- Each channel (common jumper switchable) with LED
feedback
- 2 jumpers and setup,
- 59mm x 33mm PCB size,
- 16g weight
The "LED" may be inscribed above the internal jumper indicator LEDs turn on and off (open
= disabled). This will reduce fuel consumption.


Different functional parameters:

RCS-1A (Airplane) program:
- Automatic detection servo direction,
- 1 proportional output (PWM)
- 3 Navigation Light chanel (wing, fuselage light, nose-landing)
- 1 Output Signal Lost,
- 1 Time-out (adjustable: 0.5s, 1s, 5s, 10s period),
- 2 three-way universal output.

RCS-1B (car model) program:
- Jumperelt servo direction,
- 1 pre-gas-proportional output (PWM)
- 2 output index (right and left),
- Signal Lost event jam indicator (index)
- 2 American Style bilux output
- 1 Time-out (adjustable: 1s, over time, 5s)
- 1 Reversing Output
- 1 Stop lamp output.

RCS-1C (Universal effect programs):
- Automatic detection servo direction,
- 3 kinds of main program (Jumper setupable )
- 9 progressive bypass (off + 8 levels),
- 8 sub-programs running (up to 8 different effects + program).

RCS-1D (Independent 5pcs Switch)
- Independent 5-channel switch via one servo channel,
- 3 swich max. 1A, 2 switch max. 0.5A load.

Output: Switchs:
O1 SW1
O2
O3 SW2
O4
O5 SW3
O6
O7 SW4
O8 SW5

Download (for more info): English Manual